Prw 15 PRW Billet Aluminum Stud Girdle Bedienungsanleitung PDF herunterladen

PRW Industries, Inc.

1722 Illinois Avenue

Perris, California 92571

Tele: (951) 436-7900

Tech: (888) 377-9779

PRW Aluminum Stud Girdle Installation

Instructions

Parts List

Item

Quantity

Stud Girdle for each cylinder head (either split design or one piece)

1 each

Stud Girdle RockerLoc for each valve

16 each

Step 1

Clean and inspect all parts.

Step 2

Back the set screw in the rocker arm adjuster (RockerLoc) all the way to the top of the hex end. This will

provide the proper room to set the lash on the valve.

NOTE: All rocker arm adjusters must be checked for proper clearance between the “base” or “shank” of

the RockerLocs and the inside of the upper rocker arm pivot slot. Clearance between the “base” or lower

portion of the rocker arm adjuster and the inside radius of the upper rocker arm pivot slot is critical to the

proper operation of the valve train. Rockers must maintain full range of motion without any binding or

interference between the rocker body and rocker arm adjusters.

ADDITIONAL CLARIFICATION: Before installing this aluminum stud girdle, please check to

confirm that the “base” of the stud girdle rocker arm “adjusters” (RockerLocs included with this product)

fit inside the upper rocker arm pivot “slot” and move “freely” in your rocker arm. If there is little or no

clearance, you may need to contact PRW to exchange these “adjusters” for an alternative design. Please

contact PRW Customer Service directly at 888-377-9779 or email info@PRWnetwork.com.

Step 3

Pontiac, Small Block Chevy, & Small Block Ford

After all rocker arms are in place, check to be sure that the flat side of the rocker arm trunion is facing up

for the RockerLoc to sit on. Screw the RockerLocs down onto the rockers leaving them finger tight and

do not adjust the screw.

Canted Valve Engines – Big Block Chevy & 429-460 Ford

Due to the complex valve arrangement, the installation procedure is a little different. After all rocker

arms are in place, check to be sure that the flat side of the rocker arm trunion is facing up for the

RockerLoc to sit on. The BB Chevy (BBC) design requires patience to install (particularly during the

first installation); so please follow the instructions carefully.

At this point, install only two RockerLocs in the center stud locations on the top row of BBC rocker arm

studs. These are the studs for the intake and require the longer RockerLocs. Depending upon the cylinder

heads, Ford 429-460 may or may not use the same length studs; but do use the same length RockerLocs.

1 2

Inhaltsverzeichnis

Seite 1 - Quantity

PRW Industries, Inc. 1722 Illinois Avenue Perris, California 92571 Tele: (951) 436-7900 Tech: (888) 377-9779 PRW Aluminum Stud Girdle Installat

Seite 2 - PRW Industries, Inc

Step 4 Pontiac, Small Block Chevy, & Small Block Ford Slide the stud girdle onto the RockerLocs (Make sure the machined side is facing up). It

Kommentare zu diesen Handbüchern

Keine Kommentare

Prw 15 PRW Billet Aluminum Stud Girdle Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Prw 15 PRW Billet Aluminum Stud Girdle herunter. PRW 15 PRW Billet Aluminum Stud Girdle User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Prw 15 PRW Billet Aluminum Stud Girdle